Cisco ASR 14000 Series Installation Manual Download Page 91 | Manualshive

Page: 91 / 132

background image

4-39

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 4 Installing and Removing MSCs, PLIMs, and Associated Components

How to Install or Remove an RP Card or DRP PLIM

Note

It is normal for some displayed messages to appear too briefly in the LED display to be read.

Troubleshooting the MSC

If the installed or replaced MSC fails to operate or to power up on installation:

1.

Make sure that the card is seated firmly in the Cisco ASR 14000 series 8-slot line card chassis slot.
One easy way to verify physical installation is to see whether the front faceplate of the MSC is even
with the fronts of the other cards installed in the card cage.

2.

Check whether the ejector levers are latched and that the captive screws are fastened properly. If you
are uncertain, unlatch the levers, loosen the screws, and attempt to reseat the MSC.

3.

Examine the Cisco ASR 14000 series 8-slot line card chassis alarm LEDs on the RP to see if there
are any active alarm conditions.

4.

Examine the Cisco ASR 14000 series 8-slot line card chassis power distribution units (PDUs) to see
whether the chassis, as a whole, is receiving power.

MSC Status LEDs

Use the status LEDs, located on the MSC faceplate, to verify the correct installation of the MSC:

•

When the card is properly installed, the Status LED turns green. If this LED is off, verify that the
card is installed correctly.

•

When the Status LED is blinking yellow, a problem exists on the board.

•

When the Status LED is off, the board state is unknown. Verify that there is power to the board by
looking at the indicators on the power module.

How to Install or Remove an RP Card or DRP PLIM

This section contains the following procedures:

•

Installing an RP or DRP Card

•

Removing an RP or DRP Card

•

Verifying the Installation of an RP or DRP Card

•

Installing a PCMCIA Card

•

Removing an RP PCMCIA Card

Installing an RP or DRP Card

This section describes how to install a route processor (RP) or distributed route processor (DRP) card in
the chassis. For more detailed information on the route processor card, see

Cisco ASR 14000 Series

Router 8-Slot Line Card Chassis System Description

.

Every Cisco ASR 14000 series 8-slot line card chassis contains two RP cards in dedicated slots on the
front (PLIM) side of the chassis (see

Are there comparable ASR 14000 parts and product numbers?

«
...
89
90
91
92
93
...
»

Summary of Contents for ASR 14000 Series





































































































































Reviews:

No comments

Related manuals for ASR 14000 Series

Brand: YASKAWA Pages: 68

Brand: Ubee Pages: 9

Brand: E-TOP Pages: 76

Brand: dixell Pages: 4

RS-232/422/485 Serial Card CE 3PXCC4A

Brand: B&B Electronics Pages: 47

LMP-1202M-SFP Series

Brand: ANTAIRA Pages: 2

Brand: Unex Pages: 27

Brand: CopperOptics Pages: 12

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

Brand: Tripp Lite Pages: 3

dLAN 200 AVsmart+

Brand: Devolo Pages: 2

Brand: Inter-m Pages: 20

Brand: Proxim Pages: 65

Brand: CalAmp Pages: 52

Linktropy MINI-G

Brand: Apposite Technologies Pages: 57

ibaBM-FOX-i-3o-D

Brand: IBA Pages: 13

ProCurve Radio Port 210

Brand: HP Pages: 36

StorageWorks T5521A

Brand: HP Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands