background image

 

7

Cisco Aironet Six-Element Dual-Band MIMO Patch Array Antenna (AIR-ANT25137NP-R)

OL-23461-01

  Safety Instructions

Safety Instructions

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause 
bodily injury. Before you work on any equipment, be aware of the hazards 
involved with electrical circuitry and be familiar with standard practices for 
preventing accidents. Use the statement number provided at the end of each 
warning to locate its translation in the translated safety warnings that 
accompanied this device. 

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Only trained and qualified personnel should be allowed to install, replace, or 
service this equipment.

Statement 1030

Warning

In order to comply with radio frequency (RF) exposure limits, the antennas for 
this product should be positioned no less than 6.56 ft (2 m) from your body or 
nearby persons. 

Statement 339

Follow these safety instructions when installing your antenna.

Plan your installation procedure carefully and completely before you begin.

If you are installing an antenna for the first time, for your own safety as well 
as others, seek professional assistance. Consult your dealer, who can explain 
which mounting method to use for the location where you intend to install the 
antenna.

Select your installation site with safety, as well as performance, in mind. 
Remember that electric power cables and telephone lines look alike. For your 
safety, assume that any line is an electric power line until determined 
otherwise. 

Call your local power company or building maintenance organization if you 
are unsure about cables close to your mounting location.

Summary of Contents for Aironet AIR-ANT25137NP-R

















Reviews: