manualshive.com logo in svg

Cisco Aironet 1530 Series, 1532, Installation Manual, Page: 43 / 69

Share
Download
Cisco Aironet 1530 Series, 1532 Installation Manual Download Page 43

 

2-11

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Chapter 2      Installing the Access Point

Mounting the Access Point

Mounting the Access Point

This section provides instructions for installing your access points. Personnel installing the access point 
must understand wireless access points and bridging techniques and grounding methods. 

Caution

All installation methods for mounting an access point on any wall surface is subject to the acceptance of 
local jurisdiction.

Installation Options

The 1530 Series Access Point can be wall, pole or tower mounted.There are two optional mounting kits: 
a fixed mounting kit (AIR-ACC1530-PMK1=) and a pivoting mounting kit (AIR-ACC1530-PMK2=). 

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 

Statement 1030

Warning

Installation of the equipment must comply with local and national electrical codes. 

Statement 1074

Access Point Mounting Orientation

When mounting an access point on a horizontal or vertical surface, you must ensure that the access 
point is oriented with the LED indicators pointing down. This positioning allows LEDs to be visible 
to someone on the ground below the access point.

You must also ensure the access point is mounted in such a way as to ensure that all antenna ports and 
the console port are accessible for future use.

Note

Omnidirectional antennas are vertically polarized and should be mounted vertically.

Wall Mounting the Access Point with the Fixed Mounting Kit

The optional fixed mounting kit contains a mounting bracket for wall mounting or pole mounting. 
You can use the mounting bracket as a template to mark the positions of the mounting holes for your 
installation. You then install the mounting plate, and attach the access point when you are ready. 

Table 2-1

 lists the materials you will need to provide in addition to the fixed mounting kit.

Table 2-1

Materials Required to Mount Access Point to a Vertical Wall

Materials Required to Mount Access Point to a Vertical Wall In Kit

Ground lug and screws (provided with access point)

Yes

Wall Mount Bracket

Yes

Four M6 x 12-mm Hex-head Bolts

Yes

Summary of Contents for Aironet 1530 Series, 1532






































































Reviews:

No comments