background image

   

5

Cisco Aironet 9.5-dBi Patch Antenna (AIR-ANT5195P-R)

78-16671-01

  Installing the Antenna

Site Selection

Before attempting to install your antenna, determine where you can best place the antenna for safety and 
performance.

Follow these steps to determine a safe distance from wires, power lines, and trees.

Step 1

Measure the height of your antenna.

Step 2

Add this length to the length of your tower or mast and then double this total for the minimum 
recommended safe distance.

Caution

If you are unable to maintain this safe distance, stop and get professional help.

Generally, the higher an antenna is above the ground, the better it performs. Good practice is to install 
your antenna about 5 to 10 ft (1.5 to 3 m) above the roof line and away from all power lines and 
obstructions. If possible, find a mounting place directly above your wireless device so that the lead-in 
cable can be as short as possible.

Installing the Antenna

You can install the antenna on any flat vertical surface or on a mast using the mast mounting kit. An 
articulated mast mounting kit is also available. Hardware for mounting the antenna on drywall is 
provided. If you intend to install your antenna on another surface, you must provide the appropriate 
hardware.

Tools and Equipment Required

An installation kit is shipped with the antenna and consists of the following hardware:

Four #8 x 1¾-in. sheet metal screws 

Four screw caps

Four screw cap washers

You need the following tools and equipment, which are not provided.

A #2 Phillips screwdriver

A drill

A 3/16-in. (4.8 mm) drill bit (for drywall installation; other surfaces may require a different size)

A pencil

A small mallet or hammer

The following sections contain typical procedures for installing the antenna on a vertical surface or a 
mast. Your installation may vary. Before you begin, you may want to refer to Figure 1.

Summary of Contents for AIR-ANT5195P-R - Aironet Antenna













Reviews: