Cisco 7821 Administration Manual Download

Page: 294 / 360

SIP Settings

Description

Parameter

Select the transport protocol for SIP messages:

• UDP

• TCP

• TLS

• AUTO

AUTO

allows the phone to select the appropriate

protocol automatically, based on the NAPTR records
on the DNS server. See

Configure the SIP Transport,

on page 189

for more details.

Default: UDP

SIP Transport

The phone's port number for SIP message listening
and transmission.

Specify the port number here only when you are using
UDP as the SIP transport protocol.

If you are using TCP, the system uses a random port
within the range specified in

SIP TCP Port Min

and

SIP TCP Port Max

on the

Voice

SIP

tab.

If you need to specify a port of SIP proxy server, you
can specify it using the

Proxy

field (

Proxy and

Registration, on page 286

) or the

XSI Host Server

field (

XSI Line Service, on page 289

Default: 5060

SIP Port

Support of 100REL SIP extension for reliable
transmission of provisional responses (18x) and use
of PRACK requests. Select

Yes

to enable.

Default: No

SIP 100REL Enable

The external SIP port number.

EXT SIP Port

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

280

Cisco IP Phone Troubleshooting

SIP Settings

Summary of Contents for 7821









































































































































































































































































































































































Search results

Summary of Contents for 7821

Reviews:

Related manuals for 7821

Brands by name

Popular brands

Cisco 7821, Administration Manual

Search results

Summary of Contents for 7821

Reviews:

Related manuals for 7821

Brands by name

Popular brands