Cirrus Logic CS4399 Manual Download Page 75

Page: 75 / 111

DS1113F1

CS4399

7.2 PLL Registers

7.1.9

Power Down Control

Address 0x20000

R/W

PDN_XSP

PDN_ASP

PDN_DSDIF

PDN_HP

PDN_XTAL

PDN_PLL

PDN_CLKOUT

—

Default

Bits

Name

Description

PDN_XSP

XSP input path power control. Configures XSP SDIN path power state.

0 Powered up.

1 (Default) Powered down.

PDN_ASP

ASP input path power control. Configures ASP SDIN path power state.

0 Powered up.

1 (Default) Powered down.

PDN_DSDIF DSD interface power control. Sets the power state of the DSD interface block.

0 Powered up.

1 (Default) Powered down.

PDN_HP

Power down AOUTx.

0 Powered up. The DACx are powered up.

1 (Default) Powered down. The DACx are powered down. When this bit is set, the audio outputs are soft ramped to

mute.

PDN_XTAL

Power down crystal oscillator.

0 Powered up. The XTAL driver is powered up to start generating MCLK.

1 (Default) Powered down. The XTAL driver is powered down.

PDN_PLL

PLL output power control. Sets the power state of the PLL block.

0 Powered up.

1 (Default) Powered down. PLL block is powered down.

PDN_

CLKOUT

CLKOUT output power control. Sets the power state of the CLOCKOUT output.

0 Powered up

1 (Default) Powered down. CLKOUT are driven low.

—

Reserved

7.1.10 Crystal Setting

Address 0x20052

R/W

—

XTAL_IBIAS

Default

Bits

Name

Description

7:3

—

Reserved

2:0

XTAL_IBIAS Crystal bias current strength.

010 15.0 µA

100 (Default) 12.5 µA

110 7.5 µA

Others Reserved

7.2.1

PLL Setting 1

Address 0x30001

R/W

—

PLL_START

Default

Bits

Name

Description

7:1

—

Reserved

PLL_START PLL start bit. Enable PLL output after it has been properly configured.

0 (Default) PLL is not started

1 PLL is started

Summary of Contents for CS4399
















































































































Search results

Summary of Contents for CS4399

Reviews:

Related manuals for CS4399

Brands by name

Popular brands

Cirrus Logic CS4399, Manual

Search results

Summary of Contents for CS4399

Reviews:

Related manuals for CS4399

Brands by name

Popular brands