manualshive.com logo in svg

CIRRUS DESIGN 2220, Pilot Operating Handbook

The Nokia 2220 User Manual is an essential guide for getting the most out of your device. This comprehensive manual covers all features and functions, ensuring smooth operation. Download the free manual from our website to unlock the full potential of your Nokia 2220 effortlessly.

Share
Download
background image

C

IRRUS

 D

ESIGN

S

ECTION

 3: E

MERGENCY

 P

ROCEDURES

SR20

I

NTRODUCTION

P/N 11934-005

3-3

Introduction

This section provides procedures for handling emergencies and critical 
flight situations that may occur while operating the aircraft. Although 
emergencies caused by airplane, systems, or engine malfunctions are rare, 
the guidelines described in this section should be considered and applied as 
necessary should an emergency arise.
Emergency procedures associated with optional equipment are not 
described in this section.
Although this section provides procedures for handling most emergencies 
and critical flight situations that could arise in the aircraft, it is not a substi-
tute for proper flight training, thorough knowledge of the airplane, and 
recognized piloting techniques and standards. A thorough study of the 
information in this handbook while on the ground will help you prepare for 
time-critical situations in the air.

• N

OTE

 •

Refer to 

Section 9: Log of Supplements

 for optional equipment 

Emergency Procedures.

Crew Alert System (CAS) Messaging

Warnings

Displayed in red against a black background, Warning CAS messages arise 
during emergency situations that require immediate flight crew awareness 
and immediate flight crew response.
•

A flashing Warning CAS message with an accompanying aural alert 
requires immediate action.

•

A Warning CAS message with no accompanying aural alert requires 
attention, dependent on workload. It may also require performing 
maintenance or taking corrective action prior to next flight. Warnings 
with no aural alert typically occur while on ground.

• N

OTE

 •

Crew Alerting System messages and related procedures described 

herein assume the aircraft is equipped with Garmin System Soft-

ware 2647.N3 or later.

CAPS Guidance

All Cirrus aircraft are equipped with a pilot or passenger activated ballistic 
airframe parachute system. The system is capable of lowering the aircraft 
and occupants safely to the ground for life threatening emergencies. CAPS 
provides pilots and passengers an alternative means of handling various life 
threatening emergency situations. In many cases CAPS may offer a safer 

Reissue A

Summary of Contents for 2220















































































































































































































































































































































Reviews:

No comments

Related manuals for 2220

Flylight Nynja Build Manual preview
Nynja Build
Brand: Flylight Pages: 265
Naish Cult Sport 2009 User Manual preview
Cult Sport 2009
Brand: Naish Pages: 43
Gin Gliders Gingo Owner'S Manual preview
Gingo
Brand: Gin Gliders Pages: 22
KANGKE INDUSTRIAL SUPER KRAFT PRO-FLY 540 Quick Start Manual preview
SUPER KRAFT PRO-FLY 540
Brand: KANGKE INDUSTRIAL Pages: 6
SOL paragliders Flexus 2 Manual preview
Flexus 2
Brand: SOL paragliders Pages: 41
MINIPLANE SNIP L Manual preview
SNIP L
Brand: MINIPLANE Pages: 15
SKY PARAGLIDERS 2009 excite 3 Manual preview
2009 excite 3
Brand: SKY PARAGLIDERS Pages: 69
Staufenbiel EPSILON XL3 Instruction Manual preview
EPSILON XL3
Brand: Staufenbiel Pages: 50
AVA Sport AR 18 Owner'S Manual preview
AR 18
Brand: AVA Sport Pages: 28

Brands by name

Popular brands

Load more brands