Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 40

Page: 40 / 102

SVGm

Instruction Manual



Safety shutdown,

despite the above measures, the temperature of certain components may exceed

their maximum allowable level if the device is used in environmental conditions beyond the specified

range. To avoid damaging the device or installation, the device will completely shut down automatically.

The device must be disconnected from its power supply for 30 minutes to rearm this protection

4�5�- DISPLAY

The device features a 3.5” TFT display on the front part in order to be able to view and configure all of

the parameters of the device.

Figure 35: Display�

The display enters the energy saving mode 10 minutes after the last action. To reactivate it, just touch

the display. The last screen before entering the energy saving mode will be shown.

The display is divided into three areas (

Figure 36

246

Lorem ipsum

Upper area

Central area

Lower area

Figure 36: The display is divided into three areas�

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands