Cinier Greenor Mounting Instruction Download Page 1

Thank you for choosing the 

Greenor

®

 fan coil

INSTALLATION MUST BE COMPLETED

 

BY A LICENSED MECHANICAL
OR PLUMBING CONTRACTOR.

WARNING :

Read  Carefully  -  These  instructions  contain  necessary  information  for  the  proper  installation,  use  and  efficient

 

operation of the product. Carefully read these instructions before installation and operation of the unit. Failure to

 

adhere to the instructions could result in fire, electric shock, serious personal injury, death or property damage*.

 

Save  these  instructions  and  review  frequently  for  continued  safe  operation  and  instruction  of  future  users,  if

 

necessary.
*Cinier is not responsible for any injury, loss, claim, damage, or any direct, incidental or consequential damages
of any kind which arises outside of  Cinier international manufacturer warranty.

IMPORTANT:

For all technical information regarding the installation of 

Greenor

®

 fan coils, please contact your local dealer or

 

email [email protected]

Manufacturing  defects  are  covered  under  the  manufacturing  warranty  (see  binder  or  warranty  attached).  The

 

warranty does not cover any damage arising from improper installation, improper maintenance, improper storage

 

or handling.

Remove  the 

Greenor

®

  fan  coil  from  its  box  and  separate  the  front  panel  from  the  rough  chassis  leaving  the  all

 

around protections while completing the installation of the unit. Wear thin rubber gloves when installing the unit

 

and in particular when manipulating the 

Olycale

®

 stone panel.

The installation must be made according to the manufacturer’s guidelines or using any other method considered

 

appropriate by the licensed contractor, providing it is in accordance with current legislation and local building

 

codes. 
The safety rules must be strictly respected. The radiator must be installed so that commands and panels are

 

accessible at any time.

The 

Greenor

®

 fan coil must not be installed below a power outlet. 

This fan coil heating system is not suitable for bathrooms (classe I). 
The unit must not be covered.

Greenor

®

 MOUNTING INSTRUCTION

All 

Greenor

®

 fan coils are tested and verified before expedition. If your shipment arrives clearly damaged, please

 

make a note on the receipt that the courier or other delivery party requires you to sign. Any defect noticed after

 

delivery must be reported to the manufacturer within 48 hours.

1

Summary of Contents for Greenor










Reviews: