manualshive.com logo in svg

Chungho Iguassu CT II, Technical Manual, Page: 13 / 44

Share
Download
Chungho Iguassu CT II Technical Manual Download Page 13

9

Usage

13

Ambient / Cold Water Function

There are no special setup or release functions on ambient and cold water operation. It operates auto-
matically in terms of program controlled by PCB when the power supply is on.

Hot Water Operation Setting

If hot water operation display LED is turned on by setting the hot water operation switch to “ON” posi-
tion, the hot water system will operate. How water system is operated by a detection sensor which 
automatically detects the temperature inside of the hot water tank.

Hot Water Operation Release

If the hot water operation display LED is turned off by setting the hot water operation switch to “OFF” 
position, then the hot water system stops.

*After the hot water operation switch is turned off, be careful not to be burned when you take the hot water.

Hot Water Dispense Mode

If HOT (hot water selection) touch sensor button is selected, the hot water selection LED (Red) turns 
the light on. It is the selection of hot water dispensing.

* If the hot water LED (Red) is not turned on, the hot water won’t come out even though the hot water 
dispensing button is pressed.

If you press hot water dispenser button, you can take hot water.
Release hot water dispensor button after you finish dispensing hot water.

* The hot water dispensing stops when HOT (hot water dispensing selection) touch sensor button is 
touched.

If you don’t take hot water any more, hot water dispensing function is released auto-
matically after 5 seconds from finishing hot water dispensing.

* Even if the hot water operation LED display (HOT) is turned off, you can take the water in the hot water storage tank after 

selection HOT (hot water dispensing selection) touch sensor switch button.

Cold Water Dispense Mode

Basically, it always sets on the position of cold water.
(Light on BLUE on LED display)

* When you want to take cold water after dispensing ambient water, please touch COLD/AMBI (cold water/ ambient water 

dispensing selection) touch sensor button.

It  start to dispense cold water by pressing cold water dispenser button.

* The cold water is dispensing even if AMBI (ambient water dispensing selection) touch sensor button is 
selected while cold water is dispensing.

Release cold water dispenser button after you finish dispensidng cold water.

9-1  SELECT / DESELECT FUNCTION

9-2  WATER DISPENSING

99

1

1

2

2

3

3

4

Summary of Contents for Iguassu CT II













































Reviews:

No comments