Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 335 | Manualshive

Page: 335 / 604

background image

The six ParkSense sensors, located in the front fascia/
bumper, monitor the area in front of the vehicle that is
within the sensors’ field of view. The sensors can detect
obstacles from approximately 12 inches (30 cm) up to 47 in
(120 cm) from the front fascia/bumper in the horizontal
direction, depending on the location, type and orientation
of the obstacle.

ParkSense Visual Alert

The ParkSense Warning screen will only be displayed if
Sound and Display is selected from the Customer - Pro-
grammable Features section of the Uconnect System. Refer
to

⬙

Uconnect Settings” in “Multimedia” for further infor-

mation.

The ParkSense Warning screen is located within the instru-
ment cluster display. It provides visual warnings to indi-
cate the distance between the rear fascia/bumper and/or
front fascia/bumper and the detected obstacle. Refer to
“Instrument Cluster Display” in “Getting To Know Your
Instrument Panel” for further information.

ParkSense Display

Rear Park Assist

When the vehicle is in REVERSE and an obstacle has been
detected, the warning display will turn ON indicating the
system status.

The system will indicate a detected obstacle by showing a
single arc in one or more regions based on the obstacle’s
distance and location relative to the vehicle.

If an obstacle is detected in the center rear region, the
display will show a single solid arc in the center rear region

Rear Sensor Locations

6

STARTING AND OPERATING

333

«
...
333
334
335
336
337
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

Brand: UltraGauge Pages: 55

Brand: Mercedes-Benz Pages: 30

Brand: Axxess Pages: 8

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: H&S Pages: 32

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Oypla Leisure Pages: 4

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: Ford Pages: 40

Brand: Ford Pages: 15

Brand: Honda Pages: 3

Brand: Peiying Pages: 32

Brand: Curt Manufacturing Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands