Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 171 | Manualshive

Page: 171 / 604

background image

Red Telltale Lights

Air Bag Warning Light

Red Telltale

Light

What It Means

Air Bag Warning Light

This light will turn on for four to eight seconds as a bulb check when the ignition switch is first
turned to ON/RUN. If the light is either not on during startup, stays on, or turns on while driv-
ing, have the system inspected at an authorized dealer as soon as possible. This light will illumi-
nate with a single chime when a fault with the Air Bag Warning Light has been detected, it will
stay on until the fault is cleared. If the light comes on intermittently or remains on while driving,
have an authorized dealer service the vehicle immediately. Refer to “Occupant Restraint Systems”
in “Safety” for further information.

Seat Belt Reminder Warning Light

Red Telltale

Light

What It Means

Seat Belt Reminder Warning Light

When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight sec-
onds as a bulb check. During the bulb check, if the driver’s or passenger seat belt is unbuckled, a
chime will sound. After the bulb check or when driving, if the driver’s seat belt remains unbuck-
led, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.
Refer to “Occupant Restraint Systems” in “Safety” for further information.

4

GETTING TO KNOW YOUR INSTRUMENT PANEL

169

«
...
169
170
171
172
173
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Titanium Series

Brand: Fass Pages: 13

Brand: Mitsubishi Pages: 160

Brand: Cadillac Pages: 442

Brand: Subaru Pages: 99

Gold Cruuse Cruisecontrol GC90

Brand: John Gold Pages: 24

Brand: Whispbar Pages: 14

Brand: MASCOT Pages: 12

Ride-Rite Air Helper Springs 2173

Brand: Firestone Pages: 4

Brand: Park-Daddy Pages: 22

Brand: RAM Pages: 496

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: Ecco Pages: 24

Brand: SNIPER Pages: 2

Brand: ConWys AG Pages: 16

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: TOPPOINT Pages: 2

Brand: Brodit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands