Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 106 | Manualshive

Page: 106 / 604

background image

•

Remote Start Mode Inhibit

— On vehicles equipped with

Remote Starting system, Rain Sensing wipers are not op-
erational when the vehicle is in the remote start mode. Once
the operator is in the vehicle and has placed the ignition
switch in the RUN position, rain sensing wiper operation
can resume, if it has been selected, and no other inhibit
conditions (mentioned previously) exist.

Rear Wiper And Washer

Rear Windshield Wiper Operation

Rotate the windshield wiper lever center ring upwards to
operate one of two modes for the rear window wiper:

•

First detent — intermittent mode.

•

Second detent — continuous mode.

Rear Windshield Washer Operation

Pushing the windshield wiper lever forward activates the
rear window washer. If the lever is pushed while on the
intermittent setting, the wipers will turn on and operate for
several wipe cycles after the lever is released, and then
resume the intermittent interval previously selected. If the
lever is pushed while the wipers are in the off position, the
wipers will operate several wipe cycles, then turn off.

CLIMATE CONTROLS

Overview

The Climate Control System allows you to regulate the
temperature, air flow, and direction of air circulating
throughout the vehicle. The controls are located on the
instrument panel below the radio.

NOTE:

Heating and A/C are only available with the

vehicle running, unless the vehicle is plugged in.

104

GETTING TO KNOW YOUR VEHICLE

«
...
104
105
106
107
108
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Green Motion Building

Brand: Eaton Pages: 12

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: kincrome Pages: 6

signal mirror 2005-2009 Ford Mustang

Brand: muth Pages: 9

Brand: RHOX Pages: 8

Brand: Carcomm Pages: 2

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands