manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 144 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 144

TEST

ACTION

APPLICABILITY

15

Turn the ignition off.
Disconnect the CMP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage of the (K6) 5 Volt Supply circuit in the CMP Sensor harness
connector.
Is the voltage above 5.5 volts?

All

Yes

→

Repair the short to battery voltage in the (K6) 5 Volt Supply
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

16

16

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

138

DRIVEABILITY - NGC

P0340-CAMSHAFT POSITION SENSOR CIRCUIT —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments