Chrysler 300 2017 Owner'S Manual Download Page 446 | Manualshive

Page: 446 / 488

background image

Exterior Bulbs

Bulb Number

Low Beam/High Beam (Bi-Halogen Headlamp)

Low Beam/High Beam (Bi-Xenon Headlamp)

D3S (Serviced At Authorized Dealer)

Front Turn Signal Lamp

PSY24WSV

Front Park Lamp

LED (Serviced At Authorized Dealer)

Daytime Running Lamp

LED (Serviced At Authorized Dealer)

Front Fog Lamp – If Equipped

LED (Serviced At Authorized Dealer)

Front Sidemarker Lamp

LED (Serviced At Authorized Dealer)

Rear Tail/Stop/Turn Lamp

LED (Serviced At Authorized Dealer)

Rear Sidemarker Lamp

LED (Serviced At Authorized Dealer)

Backup Lamp

LED (Serviced At Authorized Dealer)

Center High Mount Stop Lamp (CHMSL)

LED (Serviced At Authorized Dealer)

License

LED (Serviced At Authorized Dealer)

BULB REPLACEMENT

NOTE:

Lens fogging can occur under certain atmospheric

conditions. This will usually clear as atmospheric condi-
tions change to allow the condensation to change back into
a vapor. Turning the lamps on will usually accelerate the
clearing process.

Low Beam And High Beam Headlamp

High Intensity Discharge Headlamps (HID) — If
Equipped

The headlamps are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlamp switch off and the ignition turned to the OFF

444

MAINTAINING YOUR VEHICLE

«
...
444
445
446
447
448
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Jeep Pages: 6

Brand: Warrior Winches Pages: 17

Brand: iArmor Pages: 6

Brand: Kargo Master Pages: 6

Brand: SAN HIMA Pages: 10

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Lund Pages: 12

Brand: Bulldog Security Pages: 7

Brand: Ranger design Pages: 22

Brand: ACV Pages: 2

Brand: AutoMaxi Pages: 2

Brand: Blue Ox Pages: 8

EPL7SAM+C Series

Brand: Pinnacle Pages: 2

Brand: PIE Pages: 2

NANO CONNECT Smartview 72

Brand: NanoCam Plus Pages: 4

Brand: Fab Fours Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands