Chrysler 300 2017 Owner'S Manual Download Page 335 | Manualshive

Page: 335 / 488

background image

Tire Terminology And Definitions

Term

Definition

B-Pillar

The vehicle B-Pillar is the structural member of the body located be-
hind the front door.

Cold Tire Inflation Pressure

Cold tire inflation pressure is defined as the tire pressure after the
vehicle has not been driven for at least three hours, or driven less
than 1 mile (1.6 km) after sitting for a minimum of three hours. In-
flation pressure is measured in units of PSI (pounds per square inch)
or kPa (kilopascals).

Maximum Inflation Pressure

The maximum inflation pressure is the maximum permissible cold
tire inflation pressure for this tire. The maximum inflation pressure is
molded into the sidewall.

Recommended Cold Tire Inflation Pressure

Vehicle manufacturer’s recommended cold tire inflation pressure as
shown on the tire placard.

Tire Placard

A label permanently attached to the vehicle describing the vehicle’s
loading capacity, the original equipment tire sizes and the recom-
mended cold tire inflation pressures.

5

STARTING AND OPERATING

333

«
...
333
334
335
336
337
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Laser Pages: 8

Brand: Warrior Products Pages: 4

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Tessera4x4 Pages: 20

Brand: StowAway 2 Pages: 2

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: J. Strong Pages: 2

Brand: FORM FIT Pages: 2

Brand: Volvo Pages: 62

Powerbuilt 648601

Brand: AllTrade Pages: 3

SportQuest Series

Brand: Perrycraft Pages: 2

Brand: Easee Pages: 21

Brand: Nav TV Pages: 8

Brand: Haltech Pages: 13

Brand: pewag Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands