background image

 

 

 

M8 Plus User Manual 

16 

  V1.3 September 2012 

www.chroma-q.com 

Connectors: 

 

XLR-4 (male) in and XLR-4 (female) through 

European approvals:Complies with EU directives: EMC89/336/EEC Class A. Harmonised standards applied in order to verify 
compliance with directives: EN 56022:1994, EN50082-1: 1992 & EN 60950. 

North American approvals: 

Radiated Emissions: Complies with FCC part 15 subpart B, class A for unintentional radiators. 

 

 

 

Low Voltage Directive: Complies with CSA 22.2 950, UL 1950 

 

Note:

    We use the Power Unit (PU) to simplify the load calculation on any given Chroma-Q power supply. For example a PSU-

12 will supply up to 12 PU, so you can plug-in 8 M8 Plus’. 

 
 

 

3. 

Maintenance and Storage 

The M8 Plus should be stored in a dry and cool environment, safely secured to prevent from falling on a hard surface. 

The unit may be exposed to dirty environments containing many air particles. This can lead to dust and dirt build-up in the 

vents  and  fan  area.  The  unit  should  be  vacuumed  to  remove  dust  and  dirt.  This  can  be  done  with  a  painters  brush  and 

vacuum. Simply brush the dust out of the vents and fan into a vacuum cleaner. DO NOT use compressed air to blow dust 

and dirt out of the unit. 

If there is any oily residue on the body of the unit or the gel string wipe off with a damp cloth ensuring that no water enters 

the fan or vent area affecting the electronics. 

The gel string should be inspected for wrinkling and cracking. If there are signs of wear a new gel sting should be installed. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for M8 Plus





















Reviews: