Christopeit Sport 9917, Assembly And Exercise Instructions

Page: 17 / 44

17
English
Computer instructions for 9917
The supplied computer allows the most convenient training. Every value
relevant to training is displayed in a corresponding window.
From the beginning of the training session, the required time, the current
speed, the approximate calorie consumption, the travelled distance ad
the current pulse rate are displayed. All values are counted from zero
upwards.
The speed is indicated on the upper display. All other values are indicated
on the lower display.
If you wish to see one value displayed constantly as well as the speed during
training, select this with the „F“ key. If you wish to see these values in constant
alternation, select the „SCAN“ function. The display then changes from one
function to the next at intervals of approx. 6 seconds.
The computer is switched on by briefl y pressing the F- key or simply by
beginning training. The computer begins to register and display all values.
To stop the computer, just stop training. The computer stops all measurements
and retains the last attained values. The last attained values in the functions
TIME, CALORIES and KM are stored and training can continue with these
values when training is resumed.
The computer switches of automatically approx. 4 minutes after training is
stopped. All values attained until that time are stored and are displayed again
when training is resumed. It is then possible to continue training from these
values or to reset all functions to zero using the L- key.
Displays:
1. „SPEED“ display:
The current speed is displayed in kilometres per hour. It is not possible to
specify a particular value using the „E“ key. The values last attained by this
function are not stored. (Limit of the display: 99.9 km/h.)
2. „TIME“ display:
The currently required time is displayed in minutes and seconds. It is possible
to specify a particular value using the „E“ key. If a particular time
has been specifi ed, the remaining time is displayed. When the specifi ed value
is attained, this is indicated by an acoustic signal. The values last attained
by this function are stored. (Limit of the display: 99.59 minutes.)
3. „DIST“ display:
The current status of the travelled distance is displayed. It is possible to
specify a particular value using the „E“ key. If a particular distance has been
specifi ed, the remaining distance is displayed. When the specifi ed value is
attained, this is indicated by an acoustic signal. The values last attained by
this function are stored. (Limit of the display: 999 km.)
4. „CALORY“ display:
The current status of the consumed calories is displayed. It is possible to
specify a particular value using the „E“ key. If a particular consumption
has been specifi ed, the remaining number of calories to be consumed is
displayed. When the specifi ed value is attained, this is indicated by an
acoustic signal. The values last attained by this function are stored. (Limit
of the display: 999 calories.)
5. „ODO“ display:
The current status of the travelled kilometres of all previous training sessions
including current training session is displayed. A particular value cannot be
speci. ed. The values last attained by this function are not stored. (Limit of
the display: 9.999 km.)
6. „PULSE“ display:
The current pulse rate is displayed in beats per minute. It is possible to specify
a particular value using the „E“ key.
If a particular upper pulse rate limit has been specifi ed, an acoustic signal
will indicate if these limits are infringed.
The values last attained by this function are not stored. (Limit of both displays:
40 – 240 pulse beats per minute.)
Note:
For pulse measurement, the two contact surfaces of the pulse measuring
handle unit (62) must be gripped simultaneously. The contact surfaces should
be located centrally in the palms of the hands.
7. „SCAN“ function:
If this function is selected, the current values of all functions are displayed
successively in a constant sequence approx. every 5 seconds.
Keys:
1. „F“ key:
Pressing this key once briefl y makes it possible to change from one function
to another, i.e. the respective functions can be selected for which entries
can be made using the „E“ key. The currently selected function is indicated
by an icon in the respective window.
2. „E“ key:
By pressing this key once, it is possible to specify values step by step in the
respective functions. For this, the desired function must fi rstly be selected
using the „F“ key.
Holding the key pressed activates faster running, which can be stopped by
pressing the key again. When training begins, the specifi ed values are then
counted down to zero.
3. „L“ = Delete:
When this key is pressed briefl y, the values chosen with the „F“ key are
reset to zero. If the key is held longer (approx. 3 seconds), all last attained
values are deleted with the exception of the values in the „KM TOTAL“
display.