Christ Alpha 3-4 LSCbasic Operating Manual Download Page 33

Page: 33 / 97

Freeze-dryer Alpha 3-4 LSCbasic

4 Storage and transport

Version 11/2018, Rev. 1.2 of 05/03/2019

• sb-pe

33 / 97

Translation of the original operating manuel



4.3

Notes on transport

• Use suitable packaging for the transport, and if at all possible, the

original packaging.

• Install all transport safety devices (see chapter 4.5 - "Transport locking

devices").

• Over short distances, the freeze-dryer can be transported by a suitable

number of persons who reach under it from the sides.

• When lifting the freeze dryer, always reach under the freeze-dryer from

the side. Do not grab the unit at the plastic control panel (see figures
below).

correct

incorrect

Fig. 9: Lifting the freeze-dryer

CAUTION

The freeze-dryer Alpha 3-4 LSCbasic weighs approx. 86 kg!

CAUTION

The centre of gravity of the freeze-dryer is off-centre!

• When setting the unit down, ensure that the feet are upright (see figures

below).

correct

incorrect

Fig. 10: Unit feet

Summary of Contents for Alpha 3-4 LSCbasic


































































































Search results

Summary of Contents for Alpha 3-4 LSCbasic

Reviews:

Related manuals for Alpha 3-4 LSCbasic

Brands by name

Popular brands

Christ Alpha 3-4 LSCbasic, Operating Manual

Search results

Summary of Contents for Alpha 3-4 LSCbasic

Reviews:

Related manuals for Alpha 3-4 LSCbasic

Brands by name

Popular brands