Christ ALPHA 1-2 LDplus Operating Manual Download Page 30

Page: 30 / 102

Freeze-dryer Alpha 1-4 LDplus

Freeze-dryer Alpha 2-4 LDplus

4 Storage and transport

30 / 102

Version 11/2006, Rev. 2.2 of 17/10/2016

• sb

Translation of the original operating manual

Pos : 83 / 200 C hrist/ 361 GT-BA Labor-Pilot (PR OJEKT E)/Al pha/ Alpha 1-4_2- 4 LDpl us/ 040 Lagerung und Tr ansport/ 040-0030 Tr ansport hinweise Al pha 1-4_2-4 LD plus @ 35\ mod_1430379588273_68. doc x @ 258656 @ 2 @ 1



4.3

Notes on transport

• Use suitable packaging for the transport, and if at all possible, the

original packaging.

• Install all transport safety devices (see chapter 4.5 - "Transport safety

device").

• Over short distances, the freeze-dryer can be transported by a suitable

number of persons who reach under it from the sides.

• When lifting the freeze dryer, always reach under the freeze-dryer from

the side. Do not grab the unit at the plastic control panel (see figures
below).

correct

incorrect

Fig. 12: Lifting the freeze-dryer

CAUTION

The freeze-dryer

Alpha 1-4 LDplus

weighs approx. 42 kg!

The freeze-dryer

Alpha 2-4 LDplus

weighs approx. 55 kg!

• When setting the unit down, ensure that the feet are upright (see figures

below).

Fig. 13: Unit feet

Pos : 84 / 010 U ni vers al module/ Seitenwec hsel @ 0\ mod_1202116244312_0. doc x @ 105 @ @ 1

Summary of Contents for ALPHA 1-2 LDplus







































































































Search results

Summary of Contents for ALPHA 1-2 LDplus

Reviews:

Christ ALPHA 1-2 LDplus, Operating Manual, Page: 30 / 102

Search results

Summary of Contents for ALPHA 1-2 LDplus

Reviews: