Christ ALPHA 1-2 LDplus Operating Manual Download Page 31 | Manualshive

Page: 31 / 102

Christ ALPHA 1-2 LDplus Operating Manual Download Page 31

Freeze-dryer Alpha 1-4 LDplus

Freeze-dryer Alpha 2-4 LDplus

4 Storage and transport

Version 11/2006, Rev. 2.2 of 17/10/2016

• sb

31 / 102

Translation of the original operating manual

Pos : 85 / 200 C hrist/ 361 GT-BA Labor-Pilot (PR OJEKT E)/Al pha/ Alpha 1-4_2- 4 LDpl us/ 040 Lagerung und Tr ansport/ 040-0040 Verpac kung Alpha 1- 4_2- 4 LD pl us @ 35\ mod_1430379588892_68.doc x @ 258671 @ 2 @ 1



4.4

Packaging

The freeze-dryer is packaged in a cardboard box or in a wooden crate,
depending on the scope of supply.
• After opening the packaging, take out the box containing the

accessories.

• Remove the packaging material.
• Lift the freeze-dryer upwards and out of the crate/cardboard box. When

lifting the unit, always reach under the freeze-dryer from the side.

CAUTION

The freeze-dryer

Alpha 1-4 LDplus

weighs approx. 42 kg!

The freeze-dryer

Alpha 2-4 LDplus

weighs approx. 55 kg!

• Retain the packaging for any possible future transport of the freeze-

dryer.

Pos : 86 / 010 U ni vers al module/ Leerz eile @ 0\ mod_1202116244500_0. doc x @ 114 @ @ 1

Pos : 87 / 200 C hrist/ 361 GT-BA Labor-Pilot (PR OJEKT E)/Al pha/ Alpha 1-4_2- 4 LDpl us/ 040 Lagerung und Tr ansport/ 040-0050 Tr ansportsic her ung Al pha 1-4_2- 4 LDpl us @ 35\ mod_1430379589169_68. doc x @ 258686 @ 2 @ 1



4.5

Transport safety device

Prior to start-up, the vacuum sensor must be installed (see chapter 5.4 -
"Vacuum sensor").

NOTE

Prior to any transport, the vacuum sensor must be deinstalled.

Pos : 88 / 010 U ni vers al module/ Absc hnit ts wechsel @ 0\ mod_1202124514062_0.doc x @ 418 @ @ 1

Pos : 89 / 010 U ni vers al module/ Seitenwec hsel @ 0\ mod_1202116244312_0. doc x @ 105 @ @ 1

«
...
29
30
31
32
33
...
»

Summary of Contents for ALPHA 1-2 LDplus







































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands