manualshive.com logo in svg

Christ ALPHA 1-2 LDplus, Operating Manual

Share
Download
Christ ALPHA 1-2 LDplus Operating Manual Download Page 25

 

Freeze-dryer Alpha 1-4 LDplus 

Freeze-dryer Alpha 2-4 LDplus 

3 Safety 

 

 

 

Version 11/2006, Rev. 2.2 of 17/10/2016 

• sb 

25 / 102 

Translation of the original operating manual 

 

Pos :  56 / 200 C hrist/ 360  GT-BA  Labor-Pilot  (ST ANDARDM ODU LE)/ 030  Sic her heit /030-0010  Sic her heit  Labor/ 030- 0060-0010    El ektrisc he Sic herheit  @  25\ mod_1404983303448_68. doc x @  183299 @  3  @  1 

 

3.6.1 

Electrical safety 

CHRIST freeze-dryers are units of safety class I. Please comply with the 
following points in order to preserve the safety features: 

 

 

 

DANGER 

•  Ensure that the local mains voltage matches the nominal voltage that is 

stated on the name plate. 

•  Do not place any dangerous material, e.g. glass vessels containing 

liquid substances, within the safety area of 30 cm around the freeze-
dryer. Spilled liquids may get into the freeze-dryer and damage the 
electrical or mechanical components. 

•  Work on the power supply system must only be performed by certified 

electricians. 

•  Inspect the electrical equipment of the unit regularly. Defects such as 

loose or burnt cables must be eliminated immediately. 

 

 

Pos :  57 / 010 U ni vers al module/                                                                                Leerz eile @  0\ mod_1202116244500_0. doc x @  114 @   @  1 

 

 

Pos :  58 / 200 C hrist/ 360  GT-BA  Labor-Pilot  (ST ANDARDM ODU LE)/ 030  Sic her heit /030-0010  Sic her heit  Labor/ 030- 0060-0020    Mechanis che  Sicherheit  @  25\ mod_1404983304593_68. doc x  @  183313  @ 3 @  1 

 

3.6.2 

Mechanical safety 

In order to ensure the safe operation of the freeze-dryer, please comply 
with the following points: 

 

 

 

 

WARNING 

•  Do not use the freeze-dryer if it was installed incorrectly. 
•  Do not use the freeze-dryer without panels. 
•  Do not use the freeze-dryer with accessories that shows signs of 

damage. 

•  Only use the freeze-dryer with accessories that have been approved by 

the manufacturer. In case of doubt, contact the manufacturer (see 
chapter 7.3 - "Service contact"). 

•  Do not hit or move the freeze-dryer during its operation. 
•  Do not lean against or rest on the freeze-dryer during its operation. 
•  Check the freeze-dryer and the accessories before every start-up for 

any visible signs of damage. 

•  Do not dry any substances that could damage the material of the ice 

condenser chamber, drying chamber, lid, or accessories in any way, 
e.g. highly corrosive substances such as hydrogen chloride (HCl). 

•  Stop the freeze-dryer immediately in the event of a malfunction.  

Eliminate the malfunction (see chapter 7 - "Malfunctions and error 
correction") or contact the after-sales service of Firma Martin Christ 
Gefriertrocknungsanlagen GmbH (see chapter 7.3 - "Service contact"). 

•  Ensure that all repairs are performed only by authorised and 

specialised personnel. 

 

 

 

Pos :  59 / 010 U ni vers al module/ Seitenwec hsel  @  0\ mod_1202116244312_0. doc x @  105 @   @  1 

 

 

Summary of Contents for ALPHA 1-2 LDplus







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands