Chore-Time Hyflo 50454 Installation & Operator'S Instruction Manual Download Page 10

Kit Parts

36" (50485) & 48" (50454) Hyflo® Retrofit Kit

10

MV1902C

Made to work.

Built to last.

Note:  The original, authoritative version of this manual is the [English] version produced by CTB, Inc. or any of 
its subsidiaries or divisions, (hereafter collectively referred to as "CTB").  Subsequent changes to any manual 
made by any third party have not been reviewed nor authenticated by CTB.  Such changes may include, but are 
not limited to, translation into languages other than [English], and additions to or deletions from the original 
content.  CTB disclaims responsibility for any and all damages, injuries, warranty claims and/or any other claims 
associated with such changes, inasmuch as such changes result in content that is different from the authoritative 
CTB-published [English] version of the manual.  For current product installation and operation information, 
please contact the customer service and/or technical service departments of the appropriate CTB subsidiary or 
division. Should you observe any questionable content in any manual, please notify CTB immediately in writing 
to:  CTB Legal Department, P.O. Box 2000, Milford, IN 46542-2000 USA.

Revisions to this Manual

Page No.

Description of Change

Various

Added 48" Kit

Contact your nearby Chore-Time distributor or representative for additional parts and information.

CTB Inc.

P.O. Box 2000 • Milford, Indiana 46542-2000 • U.S.A.

Phone (574) 658-4101 • Fax (877) 730-8825

E-Mail: [email protected] • Internet: http//www.ctbinc.com

Printed in the U.S.A.

Summary of Contents for Hyflo 50454











Reviews: