Childcare vector pro 015616 User Manual Download Page 7

07

To adjust the seat extension

1.  Lower the seat extension by pressing up the release latches 

located underneath on both sides of the seat extension and 
push down. Then push leg support down.

2.  Raise the seat extension by pressing up the release latches and 

lift up until the release latches lock into place. 

Assembly / Operating Instructions

Positioning backrest

1.  To lower backrest, lift backrest adjusting lever.
2.  Lower backrest to desired position.
3.  To raise, simply push backrest up

CAUTION: 

Do not adjust the backrest while the child is in the stroller

Restraints - Harness

1.  To secure the child in the harness, place left 

hand buckle prong (b) on top of (a).

2.  Hold both left hand buckle prongs (a) and (b) 

together and insert it into buckle housing (e) 
until it snaps into position.

3.  Repeat previous steps for right hand buckle 

prongs (c) and (d).

4.  Once all attached, carefully adjust the harness 

straps by pulling each slider (f) until the desired 

fit is achieved in the lap, shoulder and crotch 

straps. 

5. 

To release the buckles, squeeze the top and 

bottom prongs (a) and (b), (c) and (d) together 
until harness disengages.

CAUTION: 

Always adjust the harness when 

changing the seating position of the child.

f

f

f

f

f

a

b

c

d

e

(a), (b): Left hand buckle prongs
(c), (d): Right hand buckle prongs
(e): Buckle housing
(f): Strap adjustment sliders

PLEASE NOTE:

 

This stroller has an adjustable backrest. The upright position on the backrest 

is not suitable for use with children less than six months old. For use with a newborn (0-6 
mths), the seat should be fully reclined. The backrest should only be adjusted to a more upright 
position as the child grows older and is able to support their head without assistance.

Summary of Contents for vector pro 015616

















Reviews: