background image

SL220-SK5

Service Manual

4

8.

Remove four Phillips head screws holding the SL220 to the
frame, two from the front and two from the back of the
SL220. (See Figure 5) and (See Figure 6)

9.

Remove one Phillips head screw holding the outlet box
attachment plate to the SL220. (See Figure 5)

Figure 5

10. Hold the SL220 with one hand to remove weight from the

four corner latches.

Using opening on latch, pull latch away from corner and
either push slightly away or pull slightly towards self to
lock latch within SL220 lift. (See Figure 6)

Repeat for each corner latch so that all four latches are
retracted.

Figure 6

11. Lower lift out of SL220 frame.

12. Place lift upside down on flat surface.

13. Remove four screws from bracket near control assembly.

(See Figure 7)

Figure 7

14. Remove three screws from each side of back wall and two

from top of back wall (8 screws total), and detach back wall
from SL220 assembly. (See Figure 8)

Figure 8

8

9

x 5 (total)

x

Latch

10

Hold latch
here

10

Remove Phillips

8

head screw
(others in similar
locations in front
and rear of lift)

13

x 4

Control
assembly

14

x 8

Summary of Contents for SL220-SK5









Reviews: