background image

 Model: PSH-2000

Installation Instructions

2

 IMPORTANT WARNINGS AND CAUTIONS! 

WARNING:

 A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION:

 A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the 

corresponding instructions.

WARNING:  

It is the installer’s responsibility to make sure the structure to which this unit is attached can support five 

times the combined weight of all equipment. Reinforce the structure as required before installing the unit. Failure to 
provide adequate structural strength for this unit can result in serious personal injury or damage to equipment!

WARNING:  

It is the installer’s responsibility to make sure all components are properly assembled and installed using 

the instructions provided.  Failure to follow instructions can result in serious personal injury or damage to equipment!

WARNING:  

It is the installer’s responsibility to make sure the combined weight of the display, mount, accessories, 

and any other attached equipment must not exceed 250 lbs (113 kg), the maximum support weight of this unit.  
Exceeding the maximum support weight can result in serious personal injury or damage to equipment!

WARNING:  

Make sure the latches securing the display are fully closed at all times except when removing or 

installing the display. The latches must be fully closed when installing or removing cables from the display.

CAUTION:  

Check the unit for shipping damage before you begin the installation. 

DIMENSIONS

Summary of Contents for PSH-2000









Reviews: