background image

I N S T A L L A T I O N   I N S T R U C T I O N S

Chief Manufacturing, a products division

of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280   • F:877.894.6918 / 952.894.6918

8832-000163 RevE

2009 Milestone AV Technologies,

a Duchossois Group Company

www.chiefmfg.com

06/09

BEFORE YOU BEGIN

Horizontal And Vertical Table Stands

and Accessories

Model: MSP-DCCFTP-Series

The DCCFTP-Series is a free standing, pole mount solution for multiple displays.

DCCFTP-320

DCCFTP-440

DCCFTP-220

DCCFTP-221B

DCCFTP-441B

CAUTION!

To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be
attached to it, thoroughly study all instructions and illustrations before you begin the installation.

CAUTION!

Exceeding the weight capacity can result in serious personal injury or damage to equipment!  It is the installer’s
responsibility to make sure the combined weight of all components does not exceed;

40 lbs (18.5kg) DCCFTP220/DCCFTP320                      •      50 lbs (22.68 kg) DCCFTP221

80 lbs (36kg) DCCFTP440                                              •      100 lbs (45.36 kg) DCCFTP441

If you have any questions about this installation, contact Chief Manufacturing.

Summary of Contents for MSP-DCCFTP-Series









Reviews: