background image

Installation Instructions

MFAU

7

Display Installation

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the MFAU up to (and including)
the display does not exceed 125 lbs (56.7 kg). Use with
heavier televisions may result in instability causing tip over
resulting in death or serious injury!

1.

Lay display face down on protective surface.

CAUTION:

Using screws of improper diameter may

damage your display! Proper screws will easily thread into
display mounting holes.

2.

Select screw

diameter

 by examining hardware (MA-MK)

(4mm, 5mm, 6mm or 8mm) and comparing with mounting
holes on display. (See Figure 4)

3.

Select spacers: (See Figure 4)

If mounting holes are not recessed and both
uprights (B) can lay flat against display, then no
spacers are required.

If mounting holes are recessed, or if protrusions
prevent uprights (B) from laying flat, then spacers
(ML or MM) must be used.

CAUTION:

Using screws of improper length may damage

your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.

4.

Select screw

length:

(See Figure 4)

Using your hand, insert SHORTEST length screw
of selected diameter (MA, MD, MG or MI) through
universal washer (MN), uprights (B), selected
spacer (ML or MM), into display mounting hole.
Do NOT thread screw into hole at this time.

NOTE:

Universal washers (MN) are not needed if using M8

button head cap screws (MI, MJ or MK).

Proper screw length requires base of screw head
to protrude above flat washer a

distance equal to

or greater than the screw diameter.

 If screw

length is inadequate, select longer screw. Select

shortest

 screw which will protrude the required

distance.

5.

Place uprights (B) on display, ensuring: (See Figure 4)

Center of uprights (B) are as close to the center
of the back of display as possible after being
installed. Center of bracket is indicated by the
diamond-shaped hole.

6.

Use selected screws and spacers to install two interface
uprights (B) to back of display. (See Figure 4)

Figure 4

(MA-MH) or

(MI-MK) x 4, 6 or 8

(B) x 2

6

3

(ML or MM)

5

5

Summary of Contents for MFAU













Reviews: