background image

J-Series

Installation Instructions

2

DISCLAIMER

Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries, intend to make this manual accurate and
complete. However, Milestone makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information contained in this document is subject to change
without notice or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied, regarding the
information contained herein. Milestone assumes no
responsibility for accuracy, completeness or sufficiency of the
information contained in this document.

Chief® and Centris™ are registered trademarks of Milestone
AV Technologies. All rights reserved.

 IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the
corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!  It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or
damage to equipment!  It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components located between the J-Series mount up to
(and including) the display does not exceed 75 lbs (34 kg).

DIMENSIONS

5.29

134.32

3.94

100

3.94

100

6.00

152.40

3.35

85.07

8.32

211.43

6.92

175.87

2.31

58.57

4.75

120.65

3.22

81.77

JWP

Summary of Contents for JWD











Reviews: