Chicago Welding 94164 Set Up And Operating Instructions Manual Download Page 33

IMpORtAnt!

Be CERtAIn to shut off the Welder, disconnect it from power, and discharge the torch to 

ground before adjusting, cleaning, or repairing the unit.

SKU 94164 

For technical questions, please call 1-800-444-3353.

 

Page 33

If the steps above do not solve the problem or if the repairs involved are too 

complex, contact a qualified technician.

tROUBLEShOOtInG (continued)

Wire Feeds, but Shielding gas does not Flow

pOSSIBLE CAUSES AnD SOLUtIOnS

Empty Gas Cylinder:

1. 

 

Check gas cylinder.

nozzle plugged: 

2. 

Clean nozzle.  If damaged, replace.

Regulator or cylinder valve closed:

3. 

 

Make sure both valves are adjusted properly.

Gas line blocked: 

4. 

Check external hose, and hose within Torch cable.

Gas solenoid broken or not connected properly:

5. 

 

Have a qualified technician check/replace.

LIMItED 1 YEAR / 90 DAY WARRAntY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality 

and durability standards, and warrants to the original purchaser that for a period of ninety days 

from date of purchase that the torch, liner, wire feed mechanism (if applicable), welding clamps, 

electrode holders, cables and accessories packed with the welder are free of defects in materials 

and workmanship. 

this Limited 90 Day/1 Year Warranty shall not apply to consumable parts 

such as tips, welding wire, and gas nozzles.

 Harbor Freight Tools also warrants to the original 

purchaser, for a period of one year from date of purchase, that the transformer and rectifier are free 

from defects in materials and workmanship (90 days if used by a professional contractor or if used 

as rental equipment). This warranty does not apply to damage due directly or indirectly to misuse, 

abuse, negligence or accidents, repairs or alterations outside our facilities, normal wear and tear, 

or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, 

or for incidental, contingent, special or consequential damages arising from the use of our product. 

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the 

above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU 

OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF 

MERCHANTABILITY AND FITNESS.

To  take  advantage  of  this  warranty,  the  product  or  part  must  be  returned  to  us  with 

transportation charges prepaid. Proof of purchase date and an explanation of the complaint must 

accompany the merchandise. If our inspection verifies the defect, we will either repair or replace 

the product at our election or we may elect to refund the purchase price if we cannot readily and 

quickly provide you with a replacement. We will return repaired products at our expense, but if we 

determine there is no defect, or that the defect resulted from causes not within the scope of our 

warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary 

from state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009  •  Camarillo, CA 93011  •  (800) 444-3353

Summary of Contents for 94164


































Reviews: