background image

Page 11

SKU 97994

For technical questions, please call 1-800-444-3353.

OPERATINg INSTRUCTIONS

Read the ENTIRE IMPORTANT 

SAFETY INFORMATION section 

at the beginning of this manual 

including all text under 

subheadings therein before set 

up or use of this product.

 

TO PREVENT 

SERIOUS INjURY 

FROM ACCIdENTAL 

OPERATION: 

Turn the Power Switch (11) to 

its “OFF” position before 

performing any inspection, 

maintenance, or cleaning 

procedures.

Work Piece and Work Area Set Up

Designate a work area that is clean 

1. 

and well-lit.  The work area must not 

allow access by children or pets to 

prevent injury and distraction.
Route the Power Cord (32) along a 

2. 

safe route to reach the work area 

without creating a tripping hazard 

or exposing the Power Cord to pos-

sible damage.  The Power Cord must 

reach the work area with enough 

extra length to allow free movement 

while working.
There must not be hazardous ob-

3. 

jects, such as utility lines or foreign 

objects, nearby that will present a 

hazard while working.
A barrier, such as a welding curtain 

4. 

or welding shroud should be put up 

to protect others in the work area and 

limit the spray of sparks.

general Operating Instructions

 

Protective gear 

must be worn 

when using the Plasma Cutter.   

ANSI-approved, arc shaded, 

eye protection, a full face 

shield, heavy-duty work 

gloves, a welding apron, 

respirator, and heavy-duty 

work clothes without pockets 

should be worn when using 

this product.  do not look at 

the ignited arc without eye 

protection.  Light from the arc 

can cause permanent damage 

to the eyes.  Light from the 

arc can burn the skin.  do not 

breathe arc fumes.  

IMPORTANT:  The duty cycle defines 

1. 

the number of minutes, within a 10 

minute period, during which a given 

Plasma Cutter can safely produce a 

particular current.  For example, this 

Plasma Cutter, with a 60% duty cycle 

at 10 Amps (maximum setting), must 

be allowed to rest for at least 

4 min-

utes after every 6 minutes

 of con-

tinuous cutting at 10 Amps.

Failure to carefully observe duty cy-

• 

cle limitations can stress a Plasma 

Cutter’s power generation system, 

contributing to premature plasma 

cutter failure.

This Plasma Cutter is equipped with 

• 

an internal thermal protection sys-

tem to help prevent damage to the 

unit. When the unit overheats; it au-

tomatically shuts down, then returns 

to service when it cools down.
Once the unit returns to service, fol-

• 

low a more conservative duty cycle 

Summary of Contents for 97994


















Reviews: