Chicago Electric 97906 Set Up, Operating, And Servicing Instructions Download Page 17

Page: 17 / 24

Page 17

SKU 97906

For technical questions, please call 1-800-444-3353.

troubleshooting

problem

possible causes

probable Solutions

engine will not

start

FUEL RELATED:

No fuel in tank or fuel valve closed.

Choke not in start position,

especially with cold engine.
Low quality or deteriorated, old

gasoline.
Carburetor not primed.

Dirty fuel passageways blocking fuel

flow.

Carburetor needle stuck. Fuel can

be smelled in the air.
Too much fuel in chamber. This can

be caused by the carburetor needle

sticking.

Clogged fuel filter

FUEL RELATED:

Fill fuel tank and open fuel valve.

Move choke to start position if

engine is cold.
Use only fresh 89+ octane unleaded

gasoline.
Prime carburetor by pressing

priming bulb specified number of

times (if equipped).
Clean out passageways using

fuel additive. Heavy deposits may

require further cleaning.

gently

tap side of carburetor float

chamber with screwdriver handle.
Turn choke to run position. Remove

spark plug and pull the start handle

several times to air out the chamber.

Reinstall spark plug and set choke

to start position.

Clean or replace fuel filter

IGNITION (SPARK) RELATED:

Spark plug wire not connected

securely.
Spark plug electrode wet or dirty.

Incorrect spark plug gap.

Spark plug wire or spark plug

broken.
Incorrect spark timing or faulty

ignition system.

IGNITION (SPARK) RELATED:

Connect spark plug wire properly.

Clean spark plug.

Correct spark plug gap.

Replace spark plug wire and/or

spark plug.

Have qualified technician diagnose/

repair ignition system.

COMPRESSION RELATED:

Cylinder not lubricated. Problem

after long storage periods.

Loose or broken spark plug.

(Hissing noise will occur when trying

to start.)

Loose cylinder head or damaged

head gasket. (Hissing noise will

occur when trying to start.)
Engine valves or tappets

misadjusted or stuck.

COMPRESSION RELATED:

Pour tablespoon of oil into spark

plug hole. Crank engine a few times

and try to start again.
Tighten spark plug. If that does not

work, replace spark plug. If problem

persists, may have head gasket

problem, see #3.
Tighten head. If that does not

remedy problem, replace head

gasket.
Adjust valve clearance. If that does

not work, clean or replace valves/

tappets.

Follow all safety precautions whenever diagnosing or servicing the

equipment or engine.

Summary of Contents for 97906

























Search results

Summary of Contents for 97906

Reviews:

Related manuals for 97906

Brands by name

Popular brands

Chicago Electric 97906, Set Up, Operating, And Servicing Instructions

Search results

Summary of Contents for 97906

Reviews:

Related manuals for 97906

Brands by name

Popular brands