Page 5
For technical questions, please call 1-888-866-5797.
Item 96923
Operation
Read the ENTIRE IMPORTANT
SAFEGUARDS section at the beginning
of this manual including all text
under subheadings therein before
set up or use of this product.
TO PREVENT INJURY FROM BURNS:
Allow to cool before adjusting or unloading.
CAUTION!
Vibratory finishing often creates dust
which may be harmful to your health. Wait for at
least 1 hour after vibrating is complete and the
vibrator has been turned OFF before opening
the vibrator. This will allow the dust to settle.
CAUTION!
Never vibrate with the top off, as
hazardous dust may be created, and the media or
work materials may be ejected from the vibrator.
1. Fill the Vibratory Bowl (6) about 2/3 full
with polishing media (not included).
2. Add work material parts to Vibratory Bowl. Do
not overfill Vibratory Bowl, and do not exceed
work weight limit of 18 lb. including media.
3. Place the Vibratory Lid (4) on the Vibratory
Bowl (6). Place the Flat Rubber Washer (3) and
the Flat Metal Washer (2) on the Center Shaft
(38) as shown in the Assembly Diagram.
4. Place the Clamping Nut (1) on the Center Shaft
and tighten in place. Tighten enough to keep the
Vibratory Lid (4) in place. Do not overtighten.
5. Plug in the unit and press the Power
Switch (29) to the ON position. The
Vibratory Bowl will begin to operate.
6. When the job is completed, turn the Power
Switch (29) OFF and unplug the unit.
7. Remove the Clamping Nut (1), and pull the
Vibratory Lid (4) off the Center Shaft (38) bringing
the Flat Metal Washer (2) and Flat Rubber
Washer (3) with it. Set the Lid assembly aside.
8. If a lubricant is used, then the Overflow Hose (41)
must be used to drain any excess lubricant/water
into a suitable container, preventing overflow.
9. Check the work material to determine if the
job is completed to satisfaction. If additional
work is required, replace the Lid assembly and
repeat the process. If the work is completed,
unload the work material and media.
10. Store the work material as required, and
dispose of the media. Do not reuse media.
11. To prevent accidents, turn off the appliance and
disconnect its power supply after use. Clean, then
store the appliance indoors out of children’s reach.
Maintenance
WARNING
Before inspection or maintenance, make sure the appliance’s switch is turned off,
the cord is unplugged, and the unit has cooled completely.
Do not use damaged appliances. If abnormal noise or vibration
occurs, have the problem corrected before further use.
1.
BEFORE EACH USE,
inspect the general
condition of the appliance. Check for loose screws,
misalignment or binding of moving parts, cracked
or broken parts, damaged electrical wiring, and any
other condition that may affect its safe operation.
2. Do not immerse motor, cord, or plug in water or any
other liquid.
3. After each use, dry with a soft cloth. Wipe the motor
housing with a soft clean cloth or sponge Allow unit
to dry completely before assembly or use.
Problem
Possible Causes
Probable Solutions
Appliance will not start 1. No power at outlet.
2. Cord not connected.
1. Check power at outlet.
2. Check that cord is plugged in.
Tool will not vibrate or
operates slowly
Vibratory Bowl is overloaded.
Reduce amount of material in Vibratory Bowl.
Work material is not
finished properly
1. Improper media is being used.
2. Material has not been processed
long enough.
1. Review media selection and try another option.
2. Unload excess material or extend vibration
time cycle.
