background image

Page 9

SKU 95573

for technical questions, please call 1-800-444-3353.

inSpection, Maintenance, and cleaning

warning! 

 Make sure the Power Switch is in its “OFF” position and that the 

product is unplugged from its electrical outlet before performing any inspection, 
maintenance, or cleaning procedures.

before each uSe,

 inspect the general condition of this product.  Check for loose 

screws, misalignment or binding of moving parts, cracked or broken parts, damaged 
electrical wiring, and any other condition that may affect its safe operation.  

do not 

use a damaged product.

Maintenance chart

Maintenance type

before 

use

after 

use

weekly Monthly

every 6 
Months

yearly

Inspect product for 
damage
(see #2, above)

X

Wipe off with clean, moist 
cloth

X

X

X

X

X

troubleShooting

problem

possible causes

probable Solutions

Light will not 
turn on

No power at outlet.
Power Cord (10) not 
connected.
Light Tube (19) is burned out.
Solar Panel (1) is damaged.
Solar Panel (1) is not getting 
enough sun light.
Bad Switch (21).

1.
2.

3.
4.
5.

6.

Check power at Solar Panel (1).
Check that Power cord (10) is 
plugged in.
Replace Light Tube (19).
Replace Solar Panel (1).
Relocate Solar Panel (1) to a more 
sunny location.
Replace Switch (21).

1.
2.

3.
4.
5.

6.

1.

2.

Summary of Contents for 95573












Reviews: