background image

SKU 93749 

For technical questions, please call 1-800-444-3353. 

Page 6

If you are using an extension cord 

6. 

outdoors, make sure it is marked with 

the suffix “W-A” (“W” in Canada) to 

indicate it is acceptable for outdoor 

use.
Make sure the extension cord is prop-

7. 

erly wired and in good electrical con-

dition.  Always replace a damaged 

extension cord or have it repaired by 

a qualified electrician before using it.

Protect the extension cords from 

8. 

sharp objects, excessive heat, and 

damp or wet areas.

rEcOmmENdEd miNimum WirE 

gaugE FOr EXtENSiON cOrdS* 

(120/240 VOlt)

NamEplatE

ampErES

(at full load)

EXtENSiON cOrd 

lENgtH

25’

50’

75’

100’

150’

0 – 2.0

18

18

18

18

16

2.1 – 3.4

18

18

18

16

14

3.5 – 5.0

18

18

16

14

12

5.1 – 7.0

18

16

14

12

12

7.1 – 12.0

18

14

12

10

-

12.1 – 16.0

14

12

10

-

-

16.1 – 20.0

12

10

-

-

-

taBlE a

* Based on limiting the line 

voltage drop to five volts at 

150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~

Volts Alternating Current

a

Amperes

n0 xxxx/min.

No Load Revolutions per Minute 

(RPM)

Summary of Contents for 93749













Reviews:

Related manuals for 93749