Chicago Electric 91674 Assembly And Operating Instructions Manual Download

Page: 10 / 15

SKU 91674 For technical questions, please call 1-800-444-3353. Page 10

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts List on page 14
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.

ASSEMBLY AND OPERATING INSTRUCTIONS

NOTE: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 15.

CAUTION: Always make sure the Power Cord (6) of the Sharpener is unplugged
from its electrical outlet

prior to making any adjustments to the tool.

FIGURE 1

FIGURE 2

Knob (28)

Adjusting Wheel (26)

Working Table (27)

Grinding Wheel (20)

Top View

Angle Table (30)

Angle Fence (30)

Screw (31)

Switch (5)

Adjusting Screw (26)

Number

Chisel Position

Summary of Contents for 91674
















Search results

Summary of Contents for 91674

Reviews:

Related manuals for 91674

Brands by name

Popular brands

Chicago Electric 91674, Assembly And Operating Instructions Manual

Search results

Summary of Contents for 91674

Reviews:

Related manuals for 91674

Brands by name

Popular brands