manualshive.com logo in svg

Chicago Electric 69085, Owner'S Manual

Share
Download
Chicago Electric 69085 Owner'S Manual Download Page 12

Page 12

For technical questions, please call 1-800-444-3353.

Item 69085 

        

Specifications

Electrical Rating

120V~ / 60Hz / 15A

Motor No Load Speed

6,000 RPM

Max. Accessory Diameter

9″ (230 mm)

Max. Accessory Thickness

1/4″

Arbor Hole Diameter

5/8″

Spindle Thread

5/8″ x 11 TPI

4005982

Setup - Before Use:

  Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this 

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: 

Turn the Power Switch of the tool off and unplug the tool from its electrical 

outlet before assembling or making any adjustments to the tool.

Note:

 For additional information regarding the parts listed in the following pages, 

refer to the Assembly Diagram near the end of this manual.

ASSEMBLY
Installing the Wheel Guard

TO PREVENT SERIOUS INJURY: Do not operate this tool without the Wheel Guard properly installed.

Figure 1

Wheel Guard

Bolt

Wheel 

Guard Nut

1.  Loosen the Wheel Guard Nut.

2.  Slide the collar of the Wheel Guard 

over the rim of the Gear Housing.

3.  Rotate the Wheel Guard as needed to 

shield you during the planned work.

4.  Tighten the Wheel Guard Nut securely.

5.  Check the Wheel Guard to ensure it is firmly in place. 

Adjust if necessary before proceeding.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Summary of Contents for 69085





















Reviews:

No comments

Brands by name

Popular brands

Load more brands