background image

Page 4

SKU 40765

For technical questions, please call 1-800-444-3353.

rEV 04d,07e, 07j

DO NOT OPERATE THIS MACHINE WHILE UNDER THE INFLUENCE OF ALCOHOL, 

15. 

DRUGS, OR PRESCRIPTION MEDICINES.
CHECK FOR DAMAGED PARTS. Before using any tool, any part that appears dam-

16. 

aged should be carefully checked to determine that it will operate properly and perform 

its intended function. Check for alignment and binding of moving parts, any broken parts 

or mounting fixtures, and any other condition that may affect proper operation. Any part 

that is damaged should be properly repaired or replaced by a qualified technician.

REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical re-

17. 

placement parts, which are available from Harbor Freight Tools.
DO NOT USE FOR AIRCRAFT PURPOSES.

18. 

PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE 

19. 

USE.  E

lectromagnetic fields in close proximity to heart pacemaker could cause pace

-

maker interference or pacemaker failure.  In addition, people with pacemakers should:  

Avoid operating alone. 

 

Do not use with power switch locked on. 

 

Properly maintain and inspect to avoid electrical shock. 

 

Any power cord must be properly grounded.  Ground Fault Circuit Interrupter (GFCI) 

should also be implemented - it prevents sustained electrical shock.
THE CABLE.  

20. 

Be sure the cable is in good condition, and is attached properly.  Do not 

use the Hoist if the cable is frayed, kinked, or wrapped improperly on the reel.  Do not 

replace the cable with a cable of lesser strength.
POWER SUPPLY.  

21. 

Be sure the power cord and control handle are in good condition. 

Avoid use in wet conditions, or exposing the electrical components of this hoist to mois-

ture.  Route the power cord so that it is out of the way of other tools and equipment. 

Take care to prevent damage to the power cord, or control handle cord. If the cord be-

comes damaged, repair or replace it before using the hoist.
STAND BACK.  

22. 

Stay out of the direct line that the cable is pulling. If it slips or breaks, it 

will “whiplash” along this line.  Never stand underneath a weight being lifted.  Always wear 

ANSI-approved eye protection when working around tools and equipment.  Do not hold 

the cable while using the hoist, as your hand can become caught.  Keep hands, cloth-

ing, hair and jewelry clear of the hoist while in use.  Use a spotter to assist you in assur-

ing that it is safe to operate the hoist.
POWER LIMITS.  

23. 

Do not attempt to exceed the pulling limits of this hoist.  Ensure that 

the mount to which the hoist is attached will hold the weight you will apply using this hoist.

WArning:

24. 

 This product contains or, when used, produces a chemical known to the 

State of California to cause cancer and birth defects or other reproductive harm.  (Cali-

fornia Health & Safety Code §  25249.5, et seq.)

Brought to You by www.snapwhole.com

Summary of Contents for 40765











Reviews: