background image

Page 14

For technical questions, please call 1-888-866-5797.

Item 40315 

        

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

S

E

tup

parts List and Diagram

pLEaSE rEaD tHE FOLLOWinG carEFuLLy

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM 
IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR DISTRIBUTOR 
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS 
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE 
ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY 
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND 
LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK AND LIABILITY 
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS 
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

parts List

record product’s Serial number Here: 
note:

 If product has no serial number, record month and year of purchase instead.

note:

 Some parts are listed and shown for illustration purposes only, 

and are not available individually as replacement parts.

part

Description

1

Front Cover

2

Screw M4 x 10

3

Washer M4

4

Arbor Bolt

7

Outside Flange

8

7" Blade (sold separately)

9

Inner Flange

10

Scaling Ring

11

Bolt M5 x 12

12

Lock Washer M5

13

Washer M5

14

Bolt M3 x 6

15

Splitter

16

Inner Cover

17

Tray

18

Nut M6

19

Bolt M6 x 10

20

Star Knob M8 x 16

part

Description

21

Power Switch

22

Switch Seal

23

Switch Cover

24

Inlet Clip

25

Rubber Collar

26

Washer M4

27

Screw M4 x 10

28

Copper Nut M4

29

Lock Washer M4

30

Washer M4

31

Cold Pressed Terminal

32

Copper Screw M4 x 22

33

Insulation Line

34

Power Cord/Plug

35

Nameplate

36

Ground Sign

37

3 Hole, 10 A Connector

38

Cord Clamp

part

Description

39

Capacitor

40

Screw M3 x 16

41

Motor Lead Wire

42

Motor

43

Rear Cover

44

Handle

45

Washer M6

46

Bolt M6 x 10

47

Holder

48

Square Cap

49

Blade Guard

50

Safety Label

51

Table

52

Ruler

53

Rip Fence

54

Spanner Wrench

55

Nut Driver

58

Rear Blade Cover

Summary of Contents for 40315

















Reviews: