background image

 

SDR-6220/6120

 

UHF Dual-Channel 2-Way Sync True Diversity Receiver

 

Thank  you  for choosing  this wireless microphone system! For  more  details,  please  take  a  few 
moments  to  read  this  operating  manual  to  have  a  thorough  understanding  of  the  function  and 
operation of both transmitter and receiver. 
 

In the box 

 

 

 

SDR-6220 / 6120 receiver 

two transmitters 

(handheld / belt-pack) 

a pair of antennas 

 

 

 

audio cable 

switching adaptor 

operation manual 

** Remark: The above specifications are subject to change without prior notice. 

Important 

1. 

Please make sure that the output DC voltage range of the switching power covers that 
specified by the receiver before turning it on. 

2. 

The RF meter bars and antenna diversity indicator will appear to denote RF signal received 
after turning on the transmitter.  

3. 

The receiver and transmitter must be the same frequency. 

4. 

While using the transmitter, the audio meter bars will appear to denote audio signal received. 

 

RF meter

 

Antenna selection

 

Transmitter battery 

 

Channel/frequency

 

Audio meter 

 

 

CH

FREQ

SQ

RF

AF

A B

0 0 1

630

000

VOL

CH

FREQ

SQ

RF

AF

A B

0 0 1

630

000

VOL

SDR-6120

W irele s s R e ce iv e r

S E T

S Y N C

S E T

S Y N C

CH

FREQ

SQ

RF

AF

A B

0 0 1

630

000

VOL

Summary of Contents for SDR-6220









Reviews: