background image

 

 

-1- 

Thank you purchasing CHIAYO’s professional modular wireless system. 
This versatile modular cabinet can be used for four RECEIVER modules! 
Before operation, please read this manual thoroughly to familiarize with the function of each 
part and the flexibility of this versatile cabinet. 

 
Parts and functions of QR-4000N 
 
Front panel 

 

1. Power switch. 
2. Channel 1 RECEIVER module slot 
3. Channel 2 RECEIVER module slot 
4. Channel 3 RECEIVER module slot 
5. Channel 4 RECEIVER module slot 

 
Rear panel 

 

6.  Antenna B 
7. 

MIC-LINE

 level switch. 

MIC

 level for low-impedance audio output 

LINE

 for high-

impedance audio output 

8.  Unbalanced audio output (MIXED. Switch 

 to 

LINE

 level when using this output.) 

9.  Balanced audio output (MIXED. Switch 

 to 

MIC

 level when using this output.) 

10. Channel-4 balanced audio output 
11. Channel-3 balanced audio output 
12. Channel-2 balanced audio output 
13. Channel-1 balanced audio output 
14. DC-input 
15. Antenna A 

 
Connection 

There are two kinds of audio connecters on the rear of this unit, MIC-level balanced and LINE-
level unbalanced. 
1.  Low-impedance: Mixed-

9

Individual-

10

11

12

13

 

2.  High-impedance: Mixed-

8

 

 
Use shielded audio cable for the connection between this unit and the mixer/amp or audio 
source. If the mixer/amp has a 1/4"(6.3mm) phone jack, connect a cable from the 1/4"(6.3mm) 
unbalanced audio output from the receiver to the mixer/amp. If the mixer has an XLR input, 
connect a cable from the balanced XLR audio output from the receiver to the mixer input. 

 

 

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Summary of Contents for QR-4000N









Reviews: