Chevrolet Spark 2021 Owner'S Manual Download Page 132 | Manualshive

Page: 132 / 270

background image

Chevrolet Spark Owner Manual (GMNA-Localizing-U.S./Canada-14622955) -

2021 - CRC - 8/17/20

Driving and Operating

131

Vehicle Load Limits

It is very important to know how much
weight the vehicle can carry. This
weight is called the vehicle capacity
weight and includes the weight of all
occupants, cargo, and all
nonfactory-installed options. Two labels
on the vehicle may show how much
weight it may properly carry: the Tire
and Loading Information label and the
Certification label.

{

Warning

Do not load the vehicle any heavier
than the Gross Vehicle Weight Rating
(GVWR), or either the maximum
front or rear Gross Axle Weight
Rating (GAWR). This can cause
systems to break and change the
way the vehicle handles. This could
cause loss of control and a crash.
Overloading can also reduce stopping
performance, damage the tires, and
shorten the life of the vehicle.

Tire and Loading Information Label

Label Example

A vehicle-specific Tire and Loading
Information label is attached to the
vehicle's center pillar (B-pillar). The Tire
and Loading Information label shows
the number of occupant seating
positions (1), and the maximum vehicle
capacity weight (2) in kilograms and
pounds.

The Tire and Loading Information label
also shows the tire size of the original
equipment tires (3) and the
recommended cold tire inflation

pressures (4). For more information on
tires and inflation see

and

Tire Pressure

There is also important loading
information on the Certification label.
It may show the Gross Vehicle Weight
Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) for the front and
rear axle. See

“

Certification Label

”

later

in this section.

“

Steps for Determining Correct Load

Limit

–

1.

Locate the statement "The combined
weight of occupants and cargo
should never exceed XXX kg or
XXX lbs." on your vehicle

’

s placard.

2.

Determine the combined weight of
the driver and passengers that will
be riding in your vehicle.

3.

Subtract the combined weight of the
driver and passengers from XXX kg
or XXX lbs.

4.

The resulting figure equals the
available amount of cargo and
luggage load capacity. For example,

«
...
130
131
132
133
134
...
»

Summary of Contents for Spark 2021















































































































































































































































































Reviews:

No comments

Related manuals for Spark 2021

Brand: ULTIMATE SPEED Pages: 19

Brand: CAMPARK Pages: 20

Brand: Fabbri Pages: 4

Brand: Kuda Pages: 3

Brand: Parkeon Pages: 43

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: DRAGONFIRE Pages: 4

Brand: EUFAB Pages: 18

Brand: AA Products Pages: 8

Brand: Fcar Pages: 15

Brand: PAC Pages: 7

Brand: BFT Pages: 124

2004 Silverado 1500 Pickup

Brand: Chevrolet Pages: 574

Brand: TrailFX Pages: 5

Brand: Saab Pages: 424

Brand: Volvo Pages: 193

C-Class Sedan 2018

Brand: Mercedes-Benz Pages: 2

Brand: Car Cover Division Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands