manualshive.com logo in svg

Chevrolet 2011 Camaro, Owner'S Manual, Page: 260 / 424

Share
Download
Chevrolet 2011 Camaro Owner'S Manual Download Page 260

Black plate (46,1)

Chevrolet Camaro Owner Manual - 2011

9-46

Driving and Operating

How the System Works

URPA comes on automatically
when the shift lever is moved into
R (Reverse). A single tone sounds
to indicate the system is working.

URPA operates only at speeds less
than 8 km/h (5 mph).

An obstacle is indicated by audible
beeps. The interval between the
beeps becomes shorter as the
vehicle gets closer to the obstacle.
When the distance is less than
30 cm (12 in), the beeping is
continuous for five seconds.

To be detected, objects must be at
least 20 cm (8 in) off the ground and
below trunk level. Objects must also
be within 2.5 m (8 ft) from the rear
bumper. The distance objects can
be detected may be less during
warmer or humid weather.

PARK ASSIST OFF displays on
the Driver Information Center (DIC)
to indicate that URPA is off.
The message disappears after
a short period of time.

See

Object Detection System

Messages on page 5

‑

39

for URPA

messages.

Turning the System On and Off

The URPA system can be turned
on and off using the infotainment
system controls. See

Vehicle

Personalization on page 5

‑

43

for more information.

URPA defaults to the on setting
each time the vehicle is started.

When the System Does Not
Seem to Work Properly

If the URPA system does not
activate due to a temporary
condition, the message PARK
ASSIST OFF displays on the DIC.
See

Driver Information Center (DIC)

on page 5

‑

26

for more information.

This can occur under the following
conditions:

.

The driver has disabled the
system.

.

The ultrasonic sensors are not
clean. Keep the vehicle's rear
bumper free of mud, dirt, snow,
ice, and slush. For cleaning
instructions, see

Exterior Care

on page 10

‑

94

.

.

The park assist sensors are
covered by frost or ice, which
can occur after washing the
vehicle in cold weather. Keep
the sensors free of frost or ice.

Summary of Contents for 2011 Camaro









































































































































































































































































































































































































































Reviews:

No comments