Chery S18D Service Manual Download Page 39 | Manualshive

Page: 39 / 69

Chery S18D Service Manual Download Page 39

Chery S18D Service Manual

Chapter VI Removal and Installation of Vehicle Ceiling

I. Preparations

Tools: socket wrench, cross screwdriver, slotted screwdriver and etc.

Parts: expansion bolt.

II. Precautions

1.

During the removal and installation, make sure to apply proper force and violent operation is not
allowed.

2.

During removal and installation of the inner trims, make sure to protect the tirms from being
scratched.

III. Removal and Installation of Sun Visor

1.

Removal Procedure

1.1. Use a cross screwdriver to remove the

screws on sun visor in left of the driver’s cab
and remove the sun visor.

1.2. The removal procedures for the right sun

visor are reverse to those for removal of the
left one.

2.

Installation Procedure

The installation procedures are reverse to those for removal.

IV. Removal and Installation of Ceiling Armrest

1.

Removal Procedure

1.1. Open the ceiling armrest screw cover over the

co-driver’s seat by hand, and then use a
cross screwdriver to loosen off the left and
right fixing screws.

35

«
...
37
38
39
40
41
...
»

Summary of Contents for S18D






































































Reviews:

No comments