background image

11

Figure

 A12

Carbon filter replacement

;

Carbon filter is an optional component produced with the purpose of using the range hood without 
flue connection.  If you want to use the product without flue connection, a carbon filter must be 
purchased from the authorized technical services.

Removing the carbon filter

;

 

1-

 Unplug the product and turn off the relevant fuse switch.  

2-

 Remove the aluminium filter in order to reach to the carbon filter.

3-

 Pull the carbon filter nail frontward and pull it downwards.

Fitting the carbon filter

;

Fit the nails of the carbon filter to the rear side and fixt it by pushing upwards. 

Maintenance instructions 

Unplug the product or turn off the switch before commencing maintenance works on the product. 

Aluminium filter cleaning: 

Aluminium filter is used to trap the oil particles in the air, therefore it is blocked based on the 

frequency of use and leads to performance loss with the product. Accumulated grease layer poses a 

risk of catching fire. Therefore, we recommend you to clean your filter once in two weeks. For 

cleaning, remove the filters as shown in Figure A

12

, wash with liquid detergent, rinse with water and

 

reinsert after drying. Do not use acidic, corrosive cleaning agents for cleaning the filters. Do not start 

the product without reinserting the filter. The colour of the filters may change as they are cleaned. 

This is normal and does not indicate the requirement of filter replacement. We do not recommend you 

to clean your aluminium filter in dishwasher. If the aluminium filter cannot be cleaned, you can buy a 

new one from the authorized technical service.  

Aluminium filter removal

;

Press the aluminium filter lock and remove by 

pulling down. 

Aluminium filter placement

;

Place the rear tabs of the aluminium filter in the filter 

holders in the rear side of the range, and then press 

the filter lock and push the filter up and place the 

filter in parallel position to the ground level in order to 

inset into the filter channel and release the lock.  

Section 

7A

 

Summary of Contents for LILIUM

















Reviews: