background image

- 09 -

- 10 -

following formula to calculate the shutter speed required to capture the full sequence 
of flashes:

                    

 Number of flashes / Firing frequency = Shutter speed

For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the 
shutter speed should be at least 2 sec. 

Note:

   Stroboscopic flash is most effective with a highly reflective subject against a dark background.
   Using a tripod and a remote switch is recommended.
   A flash output of 1/1 or 1/2 cannot be set for stroboscopic flash.
   Stroboscopic flash can be used with “

buLb

”.

Maximum Stroboscopic Flashes:

1/4

1/8

1/16

1/32

1/64

1/128

7

14

30

60

90

100

6

14

30

60

90

100

5

12

30

60

90

100

4

10

20

50

80

100

4

8

20

50

80

100

3

6

20

40

70

90

3

5

10

30

60

80

Flash Output

Hz

1

2

3

4

5

6

-

7

8

-

9

1/4

1/8

1/16

1/32

1/64

1/128

2

4

8

20

50

70

2

4

8

20

40

70

2

4

8

20

40

60

2

4

8

18

35

50

2

4

8

16

30

40

2

4

8

12

20

40

Hz

11

12

-

14

15

-

19

20

-

50

60

-

199

10

Flash Output

Note:

To avoid overheating and deteriorating the flash head during stroboscopic flash, do not use 

stroboscopic flash more than 10 times in succession.

8.      Hi-Speed Sync Triggering

  

To enter      mode, press <  

   

> button (18) and hold 

for 2 seconds.

  

To exit      mode, press Mode Selection Button (11) or 

press < 

   

 > button (18) and hold for 2 seconds again. 

  

In  hi-speed sync triggering mode, you can use a hi-

speed sync trigger to have your flash unit synchronized 

When “OF” is shown on the LCD display, it means no flash output and flash firing is 
turned off.

3. ZOOM: Setting the Flash Coverage

The flash coverage can be set to match the lens focal length from 24 mm to 105 mm. 

Press <   

   

> button (12) and rotate Select Dial (14) to change the flash coverage.

4. M Mode: Manual Mode

Press MODE Selection Button (11) to enter M mode. In this mode, you can set the 
flash unit onto your camera hot shoe or your trigger hot shoe for firing. 

Before shooting, adjust the flash power output. When the camera's shutter is 
pressed, the flash will fire synchronously. Slave triggering mode is not available in M 
mode.

5. S1 Mode: S1 Slave Triggering Mode

Press Mode Selection Button (11) to enter S1 mode. In this mode, the flash unit can 
function as a slave flash for creating multiple lighting effects. It is respectively 
applicable to manual flash environment.

In S1 mode, the flash unit will fire synchronously when the master flash fires, the 
same effect as that by the use of radio triggers.

6. S2 Mode: S2 Slave Triggering Mode

Press Mode Selection Button (11) to enter S2 mode. In this mode, the flash unit can 
function as a slave flash for creating multiple lighting effects. It is applicable when 
using a TTL master flash.

In S2 mode, the flash unit will ignore a single “preflash” from the master flash and will 
only fire in response to the second, actual flash from the master. 

7. RPT Mode: Stroboscopic Flash

  

Press Mode Selection Button (11) to enter RPT mode (Multi/Stroboscopic flash). 

 

  

With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture 

  

multiple images of a moving subject in a single photograph.

  

You can set the firing frequency (number of flashes per sec. expressed as Hz), the 

  

number of flashes, and the flash output.

  

For setting procedures, see the following:

1. Press the Mode Selection Button (11) so that “RPT” is displayed.

2. Press Set Button (15) to select the item to be set. The item blinks.

3. Rotate Select Dial (14) to set a desired number.

Calculating the Shutter Speed

During stroboscopic flash, the shutter remains open until the firing stops. Use the 

Fn

ZOOM

Note:

When setting the flash coverage, make sure it covers the lens focal length so that the 

picture will not have a dark periphery.

Adjust power & high 
speed triggering

Summary of Contents for V850








Reviews: