manualshive.com logo in svg

Chauvet Vue III, User Manual, Page: 15 / 17

Share
Download
Chauvet Vue III User Manual Download Page 15

General Troubleshooting 

Applies to 

Symptom Solution(s) 

Lights 

Foggers 

& Snow 

Controllers 

Dimmers
& Chaser 

Auto shut off 

Check fan thermal switch reset 

9

 

 

 

 

Beam is very dim or 
not bright 

Clean optical system or replace lamp 
Check 220/110v switch for proper setting 

9

 

 

 

 

Breaker/Fuse keeps 
blowing 

Check total load placed on device 

 

 

 

9

 

Chase is too slow 

Check users manual for speed adjustment 

9

 

 

9

 

9

 

Device has no power 

Check for power on Mains. 
Check device’s fuse. (internal and/or external) 

9

 

 

9

 

9

 

Fixture is not 
responding 

Check DMX Dip switch settings for correct addressing
Check DMX cables 
Check polarity switch settings  

9

 

 

 

 

Fixture is on but 
there is no 
movement to the 
audio 

Make sure you have the correct audio mode on the 
control switches. If audio provided via ¼” jack, make 
sure a live audio signal exists 
Adjust sound sensitivity knob 

9

 

 

9

 

9

 

Lamps cuts off 
sporadically  

Possible bad lamp or fixture is overheating. 
Lamp may be at end of its life. 

9

 

 

 

 

Light will not come 
on after power failure 

Some discharge lamps require a cooling off period 
before the electronics in the fixture can kick start it 
again, wait 5 to 10 minutes before powering up 

9

 

 

 

 

Loss of signal 

Use only DMX cables 
Install terminator 
Note: Keep DMX cables separated from power cables 
or black lights. 

9

 

9

 

9

 

9

 

Moves slow 

Check 220/110v switch for proper setting 

9

 

 

 

 

No flash 

Re-install bulb, may have shifted in shipping 

9

 

 

 

 

No laser output 

Bounce mirror motor may have shifted during 
shipping, readjust  

9

 

 

 

 

No light output 

Check slip ring & brushes for contact  
Install bulb 
Call service technician 

9

 

 

 

 

Relay will not work 

Check reset switch 
Check cable connections 

 

 

 

9

 

Remote does not 
work 

Make sure connector is firmly connected to device 

9

 

9

 

 

 

Stand alone mode 

All Chauvet lighting fixtures featuring stand-alone 
functions do not require additional settings, simply 
power the fixture and it will automatically enter into 
this mode 

9

 

 

 

 

 

If you still have a problem after trying the above solutions, please contact CHAUVET Technical 
Support at the location on the next page. 

Vue™ III User Manual 

15 

2007-05-10/15:08

 

Summary of Contents for Vue III


















Reviews:

No comments