background image

 

Scorpion™ Storm RGX User Manual 

12 

8/18/2011 

 

Fixture Linking 

You will need a serial data link to run light shows of one or more products using a DMX-512 
controller or to run synchronized shows on two or more products set to a master/slave operating 
mode. The combined number of channels required by all the products on a serial data link 
determines the number of products the data link can support.  

 

Fixtures on a serial data link must be daisy chained in one single line. To comply with the 

EIA-485 standard no more than 32 fixtures should be connected on one data link. 
Connecting more than 32 fixtures on one serial data link without the use of a DMX 
optically-isolated splitter may result in deterioration of the digital DMX signal.  

 

 

Maximum recommended serial data link distance: 500 meters (1640 ft.) 

 

Maximum recommended number of products on a serial data link: 32 products 

Data Cabling 

To link products together you must obtain data cables. You can purchase CHAUVET-certified DMX 
cables directly from a dealer/distributor or construct your own cable. If you choose to create your 
own cable please use data-grade cables that can carry a high quality signal and are less prone to 
electromagnetic interference. 

DMX Data Cable 

Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 
applications. Standard microphone cables cannot transmit DMX data reliably over long distances. 
The cable will have the following characteristics: 

2-conductor twisted pair plus a shield 
Maximum capacitance between conductors – 30 pF/ft. 
Maximum capacitance between conductor and shield – 55 pF/ft. 
Maximum resistance of 20 ohms / 1000 ft. 
Nominal impedance 100 – 140 ohms 

Cable Connectors 

Cabling must have a male XLR connector on one end and a female XLR connector on the other 

end. 

 

Do not allow contact between the common and the fixture’s chassis ground. Grounding 
the common can cause a ground loop, and your fixture may perform erratically. Test 
cables with an ohmmeter to verify correct polarity and to make sure the pins are not 
grounded or shorted to the shield or each other. 

COMMON

DMX +

DMX

 -

 

INPUT

 

OUTPUT

1

 

3

 

2

 

1

3

2

1

3

2

Resistance 120 
ohm 1/4w between 
pin 2 (DMX -) and 
pin 3 (DMX +) of 
the last product. 

Termination reduces signal errors. To 
avoid signal transmission problems 
and interference, it is always 
advisable to connect a DMX signal 
terminator.

DMX connector configuration 

Summary of Contents for Scorpion Storm RGX



















Reviews: