background image

 

T

ECHNICAL 

S

PECIFICATIONS

 

 

 

 

WEIGHT & DIMENSIONS 

Length ............................................................................................................. 9.3 in (236 mm) 
Width ............................................................................................................... 7.5 in (191 mm)  
Height ................................................................................................................. 7 in (178 mm)  
Weight .............................................................................................................. 5.2 lbs (2.3 kg) 
 

POWER 

Auto-ranging power supply ............................................................... 100~240 VAC, 50/60 Hz 
Power consumption @ 120 V ................................................. 17 W (0.2 A) max, 0.3 A inrush 
Power consumption @ 230 V ................................................. 16 W (0.1 A) max, 0.2 A inrush 
Power output ........................................................................................... 680 W, 40 units max 

 
LIGHT SOURCE 

Type ........................................................................................ high-power, single source LED 
Quantity.................................................................................................................................. 1 
Rating (white) .................................................................................... (10 W) 2.8 A, 50,000 hrs 

 
PHOTO OPTIC 

Coverage angle................................................................................................................... 33° 

 
INDOOR/OUTDOOR 

Rating ........................................................................................................ For indoor use only 

 
THERMAL 

Maximum ambient temperature ........................................................................ 104° F (40° C) 

 

CONTROL & PROGRAMMING 

Data input.............................................................................. locking 3-pin XLR female socket 
Data output .............................................................................. locking 3-pin XLR male socket 
Data pin configuration ...............................................................pin 1 shield, pin 2 (-), pin 3 (+) 
Protocol .......................................................................................................... DMX-512 USITT 
DMX Channels ....................................................................................................................... 3 
 
 

ORDERING INFORMATION 

Obsession

™ LED ........................................................................................ OBSESSIONLED 

 

WARRANTY INFORMATION 

Warranty .............................................................................................. 2-year limited warranty 

 
 

 

Summary of Contents for Obsession LED

















Reviews: