Chauvet EPIX Flex Drive User Manual Download

Page: 8 / 34

Page 5 of 31

Setup

ÉPIX Flex Drive User Manual Rev. 1

3. Setup

AC Power

The ÉPIX Flex Drive has an auto-ranging power supply and it can work with an input voltage range of 100

to 240 VAC, 50/60 Hz.

To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current

value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.

The listed current rating indicates the product’s average current draw under normal conditions.

AC Plug

The ÉPIX Flex Drive comes with a power input cord terminated with an IEC connector on one end and an

Edison plug on the other end (U.S. market). If the power input cord that came with your product has no

plug, or if you need the change the plug, use the table below to wire the new plug.

Fuse Replacement

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the safety cap out of the housing.

4. Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the

exact same type and rating.

5. Re-insert the fuse holder and reconnect power.

•

Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure

the product has an appropriate electrical ground to avoid the risk of electrocution or

fire.

•

To eliminate unnecessary wear and improve its lifespan, during periods of non-use

completely disconnect the product from power via breaker or by unplugging it.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the

rheostat or dimmer channel serves only as a 0 to 100% switch.

Connection

Wire (U.S.)

Wire (Europe)

Screw Color

AC Live

Black

Brown

Yellow or Brass

AC Neutral

White

Blue

Silver

AC Ground

Green/Yellow

Green

•

Disconnect the product from power before replacing a blown fuse.

•

Always replace the blown fuse with another of the same type and rating.

Summary of Contents for EPIX Flex Drive


































Search results

Summary of Contents for EPIX Flex Drive

Reviews:

Related manuals for EPIX Flex Drive

Brands by name

Popular brands

Chauvet EPIX Flex Drive, User Manual

Search results

Summary of Contents for EPIX Flex Drive

Reviews:

Related manuals for EPIX Flex Drive

Brands by name

Popular brands